EVO Repeller is used to repel mosquitoes, as a torch, and even as a power bank. But like other devices that are used outside it also requires to be cured and maintained so that it can last longer. This article will help you how to clean and maintain your Flextail EVO Repeller so that it will be prepared for the next use.
The Need to Maintain the Repeller
It is important to maintain your EVO Repeller for several reasons. First, it confirms that the device is functional to shield you from the mosquitoes. Second, cleaning prevents the accumulation of dirt, dust, and other deposits that can affect the functionality and longevity of the device. The last but not the least, the maintenance of the EVO Repeller will help to prolong its life and can be used in the future.
Gather Your Cleaning Supplies
To clean your EVO Repeller, you will need to gather the following items: Here’s what you’ll need:
- A soft, lint-free cloth
- A small brush (a toothbrush or a small paintbrush will do)
- Mild soap or detergent
- Water
- Isopropyl alcohol (for disinfection – not mandatory)
- Compressed air (if needed for cleaning some narrow spaces)
These supplies will help in the cleaning process and will make the process easier and faster.
Power Down and Disassemble the EVO Repeller
Before cleaning, ensure the EVO Repeller is powered down and disconnected from any power source. Remove the repellent mats, if they are still inside the device, and set them aside. If your EVO Repeller has any detachable parts, such as the lantern cover or protective casing, carefully disassemble them. This will allow you to clean each component more thoroughly.
Cleaning the Exterior of the EVO Repeller
First of all, wash the outer surface of the EVO Repeller. Wipe the surface with a soft, lint-free cloth that has been wetted only with water. For stains, wet a small piece of cloth with soap and water and clean the surface of the object. One should not use any rough materials or substances on the device since they may scratch the outer surface of the device. In case there is any blind corner or any other area that may be hard to clean, use a small brush to clean the surface. Do not rub the surface as this may lead to scratching of the surface. If you have compressed air, you can use it to blow out dust from small gaps or ventilation areas.
Cleaning of the Lantern and Light Components
The lantern, which supplies the light, is the most important part of the Repeller. It has to be cleaned so that its brightness and efficiency remain. In as much as the lantern cover is removable, it should be removed and washed with warm water and a mild soap. Wash it well and ensure that it is dry before you put it back again.
For the LED light, never wet it, but use a piece of cloth to wipe off dust or fingerprints. If there is some dirt on the light that you cannot remove using a dry cloth, then you can use a damp cloth with a little water (or a little isopropyl alcohol) and wipe the light. Make sure that water does not touch the circuit’s electronic components. If you want to read more, check out Flextail’s website.
Cleaning the Mosquito Repellent Function Area
The mosquito-repellent function of the EVO Repeller is based on heating repellent mats to emit insect-repelling vapors. In the long run, the residue from these mats may accumulate and thus influence the performance of the repeller. Before washing the parts, check if there is any breakage in the electrical parts of the LED. If there is any problem, it is advised to dial customer support and ask if the part has to be replaced.
Caring for the Battery and the Power Bank Function
The battery of the EVO Repeller is another important part as it is responsible for the power of the mosquito repellent and the lantern. To maintain the battery:
- Regular Charging
Even if you do not frequently use the EVO Repeller, the battery should be charged once in a while. This is important to maintain it and not to let it go to waste or get spoilt over some time. It is recommended that it should be charged at least once every few months.
- Avoid Overcharging
However, the EVO Repeller has been designed for long charging, and the device should be removed from the charger once it has been fully charged to avoid overcharging the battery.
- Store Properly
The battery of the EVO Repeller should be partially charged to 50% if it will not be used for some time. It is advised to store it in a cool dry place so that there is no discharge of the battery.
Reconstruction and Testing of the Device
After you have washed and dried all the parts of your EVO Repeller, it is now high time that you put it back together. When reassembling any component that was disassembled for cleaning, should do it carefully to ensure that all the parts are well-fixed. If the repellent mats are worn out then one should replace them with new ones.
Before putting the EVO Repeller away or packing it for the next use, you are advised to power it on to monitor the various operations. Check that the lantern is functioning as it is designed to do, that the mosquito repellent is functioning, and that the power bank is charging the devices.
Final Thoughts
It is thus important that the EVO Repeller is cleaned and maintained in the right manner to continue to function as required. If you have been using this guide to maintain your device, you will be confident that it is well maintained to offer you the necessary services like protecting you from mosquitoes, and a source of light and power whenever you need it. It is not only about increasing the durability of your EVO Repeller but also about making your time in the wild even more enjoyable.
