Wigs have gained a lot of attention in the beauty market because they provide different styles and lengths of hair. They can easily be integrated with natural hair and the results are perfect without the weight of other extension types. Below are the steps that will help you install your invisible tape in extensions in the right manner. This is a step-by-step guide on how to put on and take off invisible tape in extensions for that flawless look without damaging your natural hair.
What Is Invisible Tape in Extensions?
Micro bead tape-in extension is a type of hair extension that is not easily detected compared to the normal tape-in hair extension. It has a very thin and transparent adhesive tape that sticks to small portions of your natural hair; hence, the bonding is almost invisible. These extensions are preferred since they are light and can be applied easily; this makes them ideal for those who want a natural look in their hair.
Preparation
- Hair Preparation
The first step that is followed when putting the tape-in extensions is to make the correct hair parting. Start with the division of the hair from the crown along the horizontal line one inch away from the nape. Secure the upper part with clips so that it does not hinder the working process. The number of strands that will have to be left out will vary with the density of your hair as well as the width of the extensions. Last but not least, make sure that your hair is dried up after washing it to prevent bacterial formation. Tape-in extensions should be applied on clean hair and this implies that there should not be any dirt or oil on the hair. Dry your hair using a blow dryer or let it dry naturally but do not use any leave-in conditioner or any other product that may hinder the sticking of the tape.
- Tools and Products
You’ll need a few essential tools and products for the installation process. The following are some of the tools and products that will be needed during the installation process:
- Invisible Tape-In Extensions
Select good quality extensions that are as close to your hair color and type as possible.
- Tail Comb
For detangling your hair and making neat partitions.
- Extension Application Tool
This can be a tape-in extension tool or your fingers depending on what you prefer to use.
- Sectioning Clips
To ensure that the hair sections do not tangle with each other while fixing them to maintain an easy flow of the hair sections.
Installation Step-By-Step Guide
Sectioning Your Hair
Start by partitioning the hair into small sections that will be easy to work on as you create the desired style. Beginning from the crown of your head and moving downwards. Using the tail comb, part the hair and cut off the hair that you will not be styling. The more sections are split, the closer the extensions will be to real life. Moreover, click for company website for more information about the process.
Applying the Tape-In Extensions
- Separate and Tape
Choose a small strand of your hair and then place a piece of tape-in extension beneath it. The tape should be as close to the root as possible but not on the root itself. Make sure that the extension is properly pressed on your hair.
- Secure the Bond
Now, take another piece of tape-in extension and place it on top of the section, make sure that your natural hair is trapped between the two sticky tapes. Press it to make sure that the adhesive has a good hold on it. The bubbles can be flattened with the extension application tool or your fingers to ensure that the adhesive is touching the surface.
- Repeat the Process
Keep going up with the sections until you have the volume and length that you want for the look. It is also important that you blend the extensions with your hair so that one cannot even see the line.
- Blending and Styling
When all the extensions are on, make sure that you mix the extensions with your natural hair well using a brush or comb. At times, you may be asked to cut some of the extensions to make them look straight and neat. Recognize that heat or abrasive treatments are not recommended for the tape-in extensions.
How to Safely Remove Your Extensions
Preparation for Removal
The adhesive remover for tape-in extensions must be used to remove the invisible tape-in extensions. With this solution, the client’s natural hair is not harmed at all through the adhesive removal process.
Removal Process
- Apply Adhesive Remover
First, use the adhesive remover on the tape bonds. Read the instructions on the product label and wait for the time stated to allow the adhesive to dissolve.
- Gently Remove Extensions
When the adhesive is soft, carefully take out the tape-in extensions from the natural hair. Do not pull the hair as this will lead to the breaking of natural hair.
- Clean up Residual Adhesive
After this, use a mild shampoo to wash your hair so that any remaining adhesive on the hair is washed off. This should be followed by a conditioner to enable the hair to be refreshed and to be in a good state.
- Assess and Care for Natural Hair
One must evaluate the status of the natural hair that was hidden by the weave after the weave had been taken off. At times it is recommended to take off the extensions for some time to allow the hair to rest. The only drawback is that any loss of moisture during the extension process can be replenished through conditioning treatments which should be done from time to time.
Conclusion
Tape-in extensions are suitable for anyone who wants to have fuller and longer hair with a natural look. If you are the kind that loves to do it yourself or is the type that loves to get someone else to do it for you, you must know these basic steps so that your hair extension experience will not harm you. If you follow these steps, you will have a perfect installation of invisible tape-in hair extensions and get the most natural and beautiful hair without any effort. If you are still in doubt or require professional assistance, it is advisable to seek the services of INTACTE Hair.
